GMC Sierra 1500 axle shaft price snapshot
- Low
- $10
- Average
- $178
- High
- $468

Vehicle-specific price guide
A used GMC Sierra 1500 axle shaft costs $10 to $468, with a median asking price of $166. Based on 2,290 priced salvage yard listings across the US, compatible across 2007–2026 (20 model years), updated Sep 8, 2026. Prices exclude shipping, core charges, and installation.
Condition comparison
| Grade | Price range | Relative range | Listings |
|---|---|---|---|
| Grade AClean / low wear | $45–$468 | 1,345 | |
| Grade BStandard used | $10–$371 | 770 | |
| Grade CVisible wear | $50–$50 | 1 | |
| Grade XUngraded | $55–$300 | 174 |
Median by grade
Median asking price by seller-reported condition grade · $10–$468 overall range
Replacement cost
Labor is a typical independent-shop range for axle shaft replacement, not a quote for your vehicle. The part price is the live median from the salvage-yard listings on this page. How we price
Model-year comparison
Market analysis
The going rate for a used GMC Sierra 1500 axle shaft is $166 at the median, with listings spanning $10 to $468. That figure comes from 2,290 priced salvage-yard listings tracked by our index. Condition matters: grade-A units (lowest mileage, best condition) carry roughly a 240% premium over grade-C stock, with grade-A medians at $170.
Fitment variant moves the price more than most buyers expect. The most affordable variant we track, rear axle, opt ZRX (ZR2 model), lists at a $150 median, while rear axle, w/o opt ZRX; 9.5" ring gear commands $253, a 69% gap inside the same part category. Confirm which variant your VIN requires before comparing quotes.
Model year matters too: 2016 units carry the lowest median at $100, while 2024 tops the table at $225. Parts from 2007–2020 are interchangeable, so if the 2016 fits your vehicle, it offers the best value across 14 compatible years.
Against comparable vehicles, the GMC Sierra 1500 sits 23% below the Mercedes E Class ($216), 75% above the Jeep Cherokee ($95), and 23% below the Mercedes C Class ($215) for the same part. The “similar vehicles” cards below open each comparison guide.
Keep browsing this vehicle

























Price data updating














Price data updating















Price comparisons
Compare fitments
Common questions
Based on 2,290 priced salvage yard listings, a used GMC Sierra 1500 axle shaft lists between $10 and $468, with a median asking price of $166.
Using a used part, a GMC Sierra 1500 axle shaft replacement typically runs $260–$540 all-in: the median used axle shaft for this model lists at $166, and independent-shop labor for axle shaft replacement typically takes 1–2.5 hours at $95–$150/hr ($95–$375). Labor is a national part-level estimate, not a quote for your vehicle.
Condition grade, mileage, model year, and fitment variant all move the price. Our data covers 7 distinct trims/variants for this part. Check the variant table above, since interchange differences can change the price substantially. Always confirm fitment against your VIN or part number before buying.
This guide currently has year-level pricing for 2025, 2024, 2023, 2022, 2021, 2020, 2019, 2018, 2016. Other model years contribute to the overall range where sellers listed them without a year breakdown.
Based on salvage-yard interchange data, GMC Sierra 1500 axle shaft listings appear across model years 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026, suggesting these years share compatible fitments. Shopping across all 20 years may surface better prices or grades. Always verify the exact part number and VIN before buying — interchange compatibility can vary by trim or drivetrain.
A cv axle is another name for a axle shaft. The GMC Sierra 1500 axle shaft prices on this page apply — median $166, from 2,290 salvage yard listings.